- Flywheel bolts
- Lathe
- Radiator Modification?
- oil pump priming tool
- 2.8L to 3.4L swap
- Jeep won't start - I really don't think it's the battery.
- Painless wiring help needed
- Tacoma Owners - Advice Sought
- Setting initial timing
- Who can help get my '55 Jeep updated - taking recommendations
- Trying to find a V-Belt / or specs for it
- Electronic Stabilization dash lamp stuck on
- abs question
- Tacoma spark plugs
- Ramsey REP 8000
- Poor throttle response and idle
- Emissions testing
- Seeking use of a shop
- Tourque converter, or transmission issue.
- Odd noise from front diff
- Drilling holes in the Jeep body
- Welding help needed in Steamboat.
- Acetalene torch help
- Blower Motor probelms
- need welder, fabricator
- Looking for a shop that can bore some parts
- 242 transfercase
- Thoughts of using high weight engine oil
- Gear and Locker Install
- Wanna replace control arms on Jeep Rubicon TJ
- Power issue.
- Sas swap
- Radiator repair shops
- Need caster shims made
- Exhaust shops in North metro
- Voltage Regulator Question
- Lift kit install on Tacoma
- Thoughts on Hockey Puck Bump Stops
- Lockers/diff/axle etc my Silverado
- Jeep TJ 'V' Brace Behind Grill
- Porting exhaust manifolds
- Axle housing swap
- Any Cummins 12 valve guys on here?
- Early emissions test?
- stuck screw extraction nightmare
- Sway bar delete on Tacoma
- Radiator shop to recore a radiator?
- Trade tires and rims
- Need to bend some steering linkage
- Relocate sway bar disconnect retaining pin, need tap & die set
- Next Jeep project decision
- Ubolt skid plate
- Gear?
- Recommend a transmission shop?
- 98 grand cherokee limited 5.9 seems to run hot
- Anyone in the SE Metro have a press I can use?
- 3rd gen 4runner steering rack
- Bleeding brakes - 16' JKU [Fort Collins]
- Ball joint press
- HO 4.0L A/C on a Renix 4.0L
- Blind hole helicoil insert
- How to wire factory heated seats
- Gear setup?
- Warn 16.5ti on 2008 Rubicon Earthroamer
- Where to get scrap for mig practice
- Powertank refill
- Steering box rebuild gone wrong
- Need recommendations for new engine and shop install.
- D44 locker install
- old school v6 tuning question
- 12 Ton press
- Need someone with obdii scanner/ help get her started
- Teach me to weld
- Heater Core repair
- Wiring/Electrical
- What local shop might create custom pressure hose?
- Dana 44 set-up bearings...
- Non Rubi sway bar issue
- U-Joint strap slop - how much is too much - options for snugness?
- Anyone have a lab/oscilloscope scanner
- Wheel studs - Find longer or live with it?
- welding needed
- Help installing underhood air compressor
- jeep TJ gearing question
- Uh, oh... My brakes!
- Help hauling a project
- Getting new tires place cant balance
- Is this exhaust gasket correct???
- K5 topper question
- Powersteering pump rebuild
- SBC ignition problem
- P0301
- Front upper control arms on 2005 LJ
- Shop press needed
- XRC Fenders Body Armor & Cladding
- FrankenJeep Parts Ident plz - Idler pulley bearing replacement
- Rear Main Seal replacement - dig me out of a hole??
- Dana 44 Steering and info advice
- Help with modifying a clutch cable
- stuck 4Runner camber bolts...any ideas?
- Looking for a shop to respline some axle shafts
- Anyone in Noco that installs gears?
- Frame Welding
- front shimmy at highway speeds, not tires
- Gear Pattern Opinions Wanted
- How can a brake pad fail like this?
- "HotOil" warning light and warning chimes today.
- Welder needed
- Forklift freight delivery acceptance options?
- Someone to Paint My Hood
- Good Machine Shop on the front range
- Instrument panel LED lighting upgrade - dimmable?
- Cast iron repair/weld...
- NEEDED: someone to weld/install my rock sliders!
- Shop compressed air setup
- Advice for a Friend
- Noisy heim joints?
- strange noise in 4x4 Jeep JKU
- Ball Joints
- SRS able scanner for 99 xj, noco
- Plugs and wires
- Second opinion wanted (FoCo)
- 2001 Nissan Xterra 4Wd transer hard to engage.
- TJ / LJ fog lights stuck "on"
- TJ Transfer case Tragedy
- Full Hydro Steering Experience?
- Anyone know shops that mount and/or balance tires on beadlocks?
- AX15 trouble/questions
- Recommendation for body shop
- How to Remove Brown Pinstripe from a Branch?
- SYE
- Recirculation Door Actuator. 2012 JK Wrangler
- Regear advice - shop recommendations?
- Jeep 4.0 Cracked Manifold
- Battery-starter-grnd Wiring Question
- Rubber Hose for brake fluid
- Maybe a little help this afternoon?
- Differntial Cross Pin Shaft....press fit?
- Jeep XJ Service and Repair - Erie, CO
- Oil on the knuckle
- 2012 JK Wrangler starter
- Steel Tube Bending
- Control Arms Question
- What Happens Differently at 8 MPH and Below on a WK2?
- VW Bug Specialists?
- Clutch Questions
- King Coilovers and Bump Stops
- Help installing transfer case Nov 5 or 6?
- Help Wanted - sizing shock absorbers
- Talk me out of this...
- Jeep JL axle centering
- Steering wheel centering Jeep JL after lift
- Help please
- 1990 YJ Steering Box - repair or replace?
- Steel fuel line to flexible connection
- Engine Computer Resource
- need fabricator
- Car wont start - Mechanic help or recommendation
- If anyone is bored
- In search of: Front spindles - old Warn manual hub conversion kit
- Anyone have an oscilloscope (and know how to use it)?
- P0520 oil pressure sensor. JK Wrangler