Brody
May 8th, 2009, 06:49 AM
We all know how products get all sorts of advertising hype...some work as advertised, many don't. Well, about a year ago, I picked up a Drill Doctor. I use and go through a large number of drill bits, both in construction and for my fab work. Due to the fact that I have a huge amount of bits, I have been procrastinating getting started sharpening them.
I finally decided to break this unit out yesterday and give it a whirl. After getting a little confused on the written directions and boogering a few bits, I decided to watch the provided video. Lo and behold, everything I was confused on became clear and I was able to sharpen bits...and I mean SHARPEN them...and to 'unbooger' the bits I initially messed up...
I used a piece of 1/4" steel and my drill press to test the sharpness of the "new" bits. On a standard 1/2" bit that was so dull that it would have a rough time going through butter, I was able to sharpen it in about one minute. Without drilling a pilot hole, I tested it out on the 1/4" steel. It was actually sharper than what it was when new and instead of the piecemeal curlycues of steel that I was getting on a brand new bit, I ended up with quite literally, a handful of them. It hiked through the 1/4" like nothing.
In a matter of roughly an hour, I was able to sharpen probably close to $300 or more of drill bits, many of them 3/8-9/16...the more expensive ones. Some of them I added the extra split point grind to. All of these were sharpened on the default setting of 118 degrees. You can change the angle of the grind to match the material, with settings up to 135 degrees. You can also sharpen masonry bits and various others. There is an additional attachment that allows you to sharpen up to 3/4" which I am planning on purchasing.
Since I like the split point self locating bits, I have a lot of these...many dull. You know the ones...they have the cute little extra point on the end of the bit. The real test for me was to sharpen these. The Drill Doctor will not sharpen these in the manufacturer's configuration and you have to 'massage' the tip off. I used a grinding wheel (subtle, I know) to get rid of the tip. Then I followed the instructions and put a nice grind on the 'new' bit. It worked fine and I got the same results as with the regular bits. I was careful to stick the bit it water as I ground the tip off to keep it from losing it's temper.
Anyway, for $100, if you have a bunch of drill bits that are dull, this is a most worthwhile investment, even though it looks like it was made by Mattel due to the amount of plastic used. I already made my $$ back and it just looks dusty.
Here is the link to BillaVista's write up on the same unit:
http://www.pirate4x4.com/tech/billavista/PR-DrillDr/index.html
My rating on this product::thunb::thunb::thunb::thunb::thunb:
I finally decided to break this unit out yesterday and give it a whirl. After getting a little confused on the written directions and boogering a few bits, I decided to watch the provided video. Lo and behold, everything I was confused on became clear and I was able to sharpen bits...and I mean SHARPEN them...and to 'unbooger' the bits I initially messed up...
I used a piece of 1/4" steel and my drill press to test the sharpness of the "new" bits. On a standard 1/2" bit that was so dull that it would have a rough time going through butter, I was able to sharpen it in about one minute. Without drilling a pilot hole, I tested it out on the 1/4" steel. It was actually sharper than what it was when new and instead of the piecemeal curlycues of steel that I was getting on a brand new bit, I ended up with quite literally, a handful of them. It hiked through the 1/4" like nothing.
In a matter of roughly an hour, I was able to sharpen probably close to $300 or more of drill bits, many of them 3/8-9/16...the more expensive ones. Some of them I added the extra split point grind to. All of these were sharpened on the default setting of 118 degrees. You can change the angle of the grind to match the material, with settings up to 135 degrees. You can also sharpen masonry bits and various others. There is an additional attachment that allows you to sharpen up to 3/4" which I am planning on purchasing.
Since I like the split point self locating bits, I have a lot of these...many dull. You know the ones...they have the cute little extra point on the end of the bit. The real test for me was to sharpen these. The Drill Doctor will not sharpen these in the manufacturer's configuration and you have to 'massage' the tip off. I used a grinding wheel (subtle, I know) to get rid of the tip. Then I followed the instructions and put a nice grind on the 'new' bit. It worked fine and I got the same results as with the regular bits. I was careful to stick the bit it water as I ground the tip off to keep it from losing it's temper.
Anyway, for $100, if you have a bunch of drill bits that are dull, this is a most worthwhile investment, even though it looks like it was made by Mattel due to the amount of plastic used. I already made my $$ back and it just looks dusty.
Here is the link to BillaVista's write up on the same unit:
http://www.pirate4x4.com/tech/billavista/PR-DrillDr/index.html
My rating on this product::thunb::thunb::thunb::thunb::thunb: